YOUR USS OIL CHANGE GUIDE

NEED AN OIL CHANGE?

A SIMPLE STEP BY STEP GUIDE, IT’S EASIER THAN IT SOUNDS.

How to change your motor oil

It's important to remember that when it comes to maintenance, safety always comes first. So whether you're a first-timer or an old hand, The Expert has put together this step-by-step tutorial to show you the safest and most efficient way to perform this simple task.

What you'll need:

• Approximately 5 litres of United Synthetic Specialists motor oil. (Check your manual for the proper SAE viscosity, API performance and quantity required for your engine.)
• A new oil filter. Most cars use a "spin-on" oil filter available in various sizes. (The USS Black Widow Ultra OEM Spec is an ideal choice.)
A drain plug socket wrench or open-end spanner (correct size) and an oil filter wrench. Some engines require a specially shaped tool that can be purchased from your local parts supplier. A large drain pan, at least 6-8 litres in capacity and a funnel.
• Clean rags, hand-cleaning solution and/or disposable latex gloves.

Oil change step 1 - Choose your motor oil

• If your schedule involves frequent short trips, stop-and-go traffic or towing and hauling, the extra strain on your engine will necessitate more frequent changes.
• Be certain to check your owner's manual for special conditions and do not exceed warranty recommendations.

Oil change step 2 - Prepare your vehicle

• Always be certain to consult your owner's manual for specific safety precautions before climbing under your vehicle.
• Never use a jack to hold your vehicle up - it's simply too unstable. Portable wheel ramps are ideal and much safer. Wheel ramps will tilt the car just enough to allow you to slide underneath. Make sure you follow your wheel ramp manufacturer's instructions carefully, especially concerning safety issues.
• After making sure that you are on level ground, drive your vehicle up onto the wheel ramps so that the front tyres are elevated. Set your handbrake, and brace both rear wheels with wooden blocks to prevent the vehicle from rolling.
• Put your vehicle in first gear if you have a manual transmission or in “Park” if you have an automatic transmission.
• Cold oil will not drain properly, so before starting work, drive your car around to raise the oil temperature to bring it to normal operating temperature. Then switch off the engine and raise the bonnet to loosen the oil filler cap to avoid creating a vacuum. This will allow the oil to drain from the bottom more freely.

Oil change step 3 - Drain the old oil

• Locate the oil drain plug on the underside of your vehicle. It should be located at the bottom rear end of the engine sump or oil pan.
• Place the drain pan underneath the drain plug and slightly toward the back. Using your spanner, turn the plug counterclockwise until it rotates freely. Finish removing the plug by hand. At this point, be careful of the oil since it may release rapidly and is likely to be rather hot. Try not to drop the plug into the pan, but don't worry if you do!

Note: Most drain plugs also use a sealing washer; be careful not to lose this!

Oil change step 4 - Remove the oil filter

• Loosen the oil filter by turning it counterclockwise with a filter wrench. Complete the removal by hand, taking care not to touch the hot exhaust manifold. The oil filter may be filled with oil and feel slightly heavy, so carefully ease it down and away from the engine and tip its contents into the drain pan. Note: some oil filters are mounted horizontally and when you loosen them they will leak some dirty, hot engine oil. Don't worry, this is normal, but be ready for the leak by having several absorbent rags. Take your rag and wipe in and around the filter seat on the engine.

Oil change step 5 - Replace the oil filter

• Take your rag and wipe in and around the filter seat on the engine.
• Then take a new filter and use your finger to apply a light film of oil (new or used) to the gasket (the circular edge of the filter itself), which acts as a sealant.
• Carefully screw the new filter onto the threaded oil line, turning it clockwise.
• Once aligned properly, the filter will thread on easily. Tighten the filter by hand, taking care not to over tighten.
• Clean the oil plug and sealing gasket and then align and replace the plug.
• Screw the plug in by hand and finish by tightening it with a wrench. Once again, don't over tighten.

Oil change step 6 - Add clean oil

• Carefully release the handbrake and allow the car to slowly roll back down the ramp to level ground (do not run the engine at this stage or severe damage will occur).
• On the top of the engine you will find the Oil Filler Cap usually marked with the symbol of an oil can. Unscrew the cap and proceed to fill the engine with the required quantity of oil, checking with the dipstick to ensure proper fill level.
• Replace the cap and wipe off any spillage. The oil light should go out as soon as the engine is started.
• Run the engine for several minutes, then switch it off and check the dipstick once again to ensure proper oil level. It is likely that you will have to add some more oil at this point.
• Last, but not least, check under the vehicle for leaks - especially around the oil filter and sump drain plug.

Oil change step 7 - Dispose of used oil

• The final, and in some ways most important, step to your oil change is the proper disposal of the used oil that you have drained from your vehicle. Used motor oil is highly toxic to the environment and it's of the utmost importance that it's disposed of in a safe fashion.
• Transfer the used oil to a sealed container and consult your local garage about options for safe disposal. Chances are that a garage in your area will take the oil off your hands and arrange for it to be recycled or safely disposed of. You could also contact an environmental agency that can direct you towards an alternative option.
• Keep a written record of the kilometres and date for each oil change. That way, it will be easy to keep track of when your next change should take place.